Beckett AFG Oil Burner Specifications

RWB 6104 BNX Page 1To the Professional, Qualifi ed Installer or Ser-vice Agency:Please read and carefully follow all instructions provided in this

Page 10 RWB 6104 BNX The burner may be equipped with a single-stage fuel unit for these installations. Connect the fuel supply to the burner with a

RWB 6104 BNX Page 11Wiring Connections Diagram•Start the Burner and Set CombustionFollow the appliance manufacturer’s wiring dia-grams and note al

Page 12 RWB 6104 BNX Typical Burner Sequence of Operation for GeniSys 7505 Control.Refer to the appliance manufacturer’s wiring diagram for actual sp

RWB 6104 BNX Page 13Table 6 - Status LightsLight Color On Continuously FlashingRed Restricted (Hard) Lockout Soft LockoutGreen Flame Sensed during

Page 14 RWB 6104 BNX 613517. RECYCLE. If the fl ame is lost while the burner is fi ring, the control shuts down the burner, enters a 60 second recycle

RWB 6104 BNX Page 15 The R7184 primary control with valve-on delay and burner motor-off delay, shown in Figure 9, requires a constant 120 volt AC

Page 16 RWB 6104 BNX Start the Burner and Set CombustionTurn the air adjustment screw counterclock-wise to adjust the plate with the pointer to the z

RWB 6104 BNX Page 17OIL-BURNING EQUIPMENT SHALL BE CONNECTED TO !!CAUTIONFLUES HAVING SUFFICIENT DRAFT AT ALL TIMES TO ENSURE SAFE AND PROPER OPER

Page 18 RWB 6104 BNX Trained Service Technician’s Regular Maintenance The following guidelines are provided for routine maintenance. Replace the oil

RWB 6104 BNX Page 19Nozzle Installation •Perform Regular Maintenance Perform the following steps when replacing a nozzle.Remove the nozzle l

Page 2 RWB 6104 BNX

Page 20 RWB 6104 BNX Figure 12. – Electrode tip gap and spacing 5/32” GAP1/4” above nozzle center3/32” Nozzle-to-tip SpacingSK9664Perform Regular Mai

RWB 6104 BNX Page 21Perform Regular MaintenanceFigure 13 – Retention Head/Throttle Cup AlignmentCheck/Adjust “Zero” Calibration On burners with f

Page 22 RWB 6104 BNX For best performance specify genuine Beckett replacement partsReplacement Parts Diagram

RWB 6104 BNX Page 23Item Description Part No.1 Air guide 101101U2 Head/Air adjustment mecha-nism assembly52000U3 Splined nut 36664 Coupling 24545

Page 24 RWB 6104 BNX LimitedWARRANTYFor Residential, Commercial and Specialty Burners The R. W. BECKETT CORPORATION (“Beckett”) warrants to persons w

RWB 6104 BNX Page 3Table of ContentsGeneral Information Hazard Defi nitions ...

Page 4 RWB 6104 BNX Hazard Defi nitions Owner’s ResponsibilityContact a professional, qualifi ed service agency for the installation, adjustment and se

RWB 6104 BNX Page 5 To the Owner: Thank you for purchasing a Beckett burner for use with your heating appliance. Please pay attention to the Saf

Page 6 RWB 6104 BNX Please read and understand the manual supplied with this equipment. This equipment must be installed, adjust-ed and put into oper

RWB 6104 BNX Page 7The fl ue pipe should have an upward pitch toward the chimney of at least 1/4” per foot of length. It should fi t tightly and sho

Page 8 RWB 6104 BNX Inspect/Prepare Installation SiteClearances to burner and applianceProvide space around burner and appliance for easy service and

RWB 6104 BNX Page 9Inspect/Prepare Installation Site Always install fi ttings in accessible locations. To avoid vibration noise, fuel lines should