Beckett CF800 Instruction Manual

COMMERCIAL PRODUCTSPotential for Fire, Smoke and Asphyxiation HazardsTo the Homeowner or Equipment Owner: y Please read and carefully follow all instr

10Set dimension Z ○ Loosen fastener c in Figure 7. Slide the nozzle line and plate assembly until dimension Z in Figure 6 is:CF500 - 1-9/16” ±1/16”C

11CF500/CF800 Burner Manualgearset fl ow capacity (Table 3) for two-pipe systems. Size the fi lter for the fi ring rate for one-pipe systems. Locate the

12Figure 10. – Typical Wiring (7505P)Section: Wire the BurnerLIMITSDETECTORAKDAACFSUPPLIED BY INSTALLERFROM FUSED DISCONNECT SWITCHLINE VOLTAGE SERVIC

13CF500/CF800 Burner ManualFigure 11 - 7505 Control Fire or Explosion HazardCan cause severe injury, death, or property damage. y The control can malf

145. Ignition Carryover: Once fl ame is established, the igniter remains on for 10 additional seconds to ensure fl ame stability. 6. Run: The fl ame is

15CF500/CF800 Burner ManualTable 4 - Reset Button OperationIf the burner is in thebelow state:Pushing the reset button will:Button Click(press < 1

161. STANDBY. The burner is idle, waiting for a call for heat. When a call for heat is initiated, there is a 3-10 second delay while the control perfo

17CF500/CF800 Burner ManualPrepare the Burner for Start-upStart-up checklist - Verify the following before attempting to start burner. □ Combustion ai

18 □ Fuel connection to nozzle line assembly is secure. □ Dimension Z has been set per the ‘Set Z Dimension’ instructions detailed earlier in this man

19CF500/CF800 Burner Manual- Priming the Pump For 7505 Control: ○ Initiate a call for heat. ○ After the burner starts, press and hold the reset button

2

20 Cad Cell Resistance Measurement ○ If the Beckett 7505 control is equipped with the GeniSys Display Module, part 52067U, the cad cell resistance ca

21CF500/CF800 Burner ManualMaintenance and ServiceAnnual Professional Service RequiredTampering with or making incorrect adjustments could lead to equ

22Replacement parts1231098456722Figure 13 - Adjustable mounting plates for CF500 and CF800121113141516Section: Replacement Parts

23CF500/CF800 Burner ManualSection: Replacement PartsItem Part Name/Description Part Number1 Air Tube Specify2 Spline Nut 36663 Adjusting plate assemb

USA: P.O. Box 1289 ● Elyria, Ohio 44036Canada: R.W. Beckett Canada, Ltd. ● Unit #3, 430 Laird Road ● Guelph, Ontario N1G 3X7www.beckettcorp.comPart Nu

3CF500/CF800 Burner ManualTo the Owner:Thank you for purchasing a Beckett burner for use with your heating appliance. Please pay attention to the Saf

4Agency approvals ○ UL listed to comply with ANSI/UL296 and certifi ed to CSA B140.0. ○ Accepted by N.Y.C. M.E.A. ○ Other approvals may be available an

5CF500/CF800 Burner ManualCombustion air supplyOwner’s Responsibility:Professional Installer/Service Agency Responsibility:Pre-installation ChecklistT

6the fuel unit (oil pump) on the burner. Refer to fuel unit literature in the literature envelope in the burner carton to verify allowable suction pre

7CF500/CF800 Burner ManualVerify Firing RateRefer to appliance manufacturer’s instructions (if available) for fi ring rate and nozzle selection. Otherw

8Firebox pressure (in w.c.)CF500 CF800 CF500 CF800Tube KKTube KHTube KJTube KKTube KHTube KJNo reserve air 10% Turndown0.0” 5.50 7.00 8.00

9CF500/CF800 Burner ManualMount fl ange(s) on air tubeThis section does not apply to burners with welded fl anges.1. Do not install air tube on burner.